Podcast Review: On the Line with… Designing for Reality
May 9, 2024 | Duane Benson, Positive Edge LLCEstimated reading time: 6 minutes
As a technologist, if I were forced to come up with just one recurring theme that I might call a professional “nemesis,” it would be the difference between theory and reality. A lot of technology we have at our disposal works well in theory but falls short when reality hits. That’s not the only reason I chose to listen to and review On the Line with… Designing for Reality, featuring a series of conversations with ASC Sunstone’s Matt Stevenson, but it certainly helped that the title caught my eye.
I have decades of experience in electronics design and manufacturing, including nearly 20 years in a leading quick-turn PCB assembly company. In that time, I have found that the pedigree of the engineer and the stature of the company sending in a design to be manufactured has little correlation to the quality and manufacturability of the product. Big company, small company, university, start-up designer, degreed electronics engineer or self-taught electronics designer—it doesn’t seem to matter. All are subject to the same traps, and all are as capable of making successful or failed designs as any other. The most common failures I have run across relate to inadequate consideration of the reality of manufacturing constraints. In this podcast, Matt dives into the reality of the design and manufacturing process and does his best to enlighten listeners to what they need to know to create designs that are manufacturable under real-world conditions.
Episode 1: Designing for Reality—What Is It?
Matt’s first episode, moderated by I-Connect007’s Nolan Johnson, starts off with a bit of a recap of Matt’s book of the same name. I’ve read the book and it’s worth reading. At the beginning of this episode, Matt talks about the importance to an electronics designer of understanding their manufacturing partners. I cannot agree more. A solid design on paper is a good thing. However, it is nothing until it has been built up and is working. Matt states that manufacturability should be “the goal of the lion’s share of design,” and I strongly agree. An unmanufacturable design is not a design. It is time and money wasted.
Yes, it’s about chemistry and physics.
Matt mentions how much he enjoys giving factory tours and that he likes to discuss the physics and chemistry involved in fabricating printed circuit boards. I start to get really interested when basic sciences are called out. It’s not an absolute requirement to know about what’s beneath the technology you are using, but I have always found that end designs are easier when I do understand why and how the electrons are moving around.
It’s clear that both Matt and Nolan understand the technology they are discussing. They deliver information in an easy conversational style. It’s also evident that Matt is, first and foremost, an engineer and a builder of things. I find it refreshing when information and content get priority over gloss and polish. This podcast is simply two very knowledgeable people trying to help electronics designers by giving insight into the manufacturing process.
Episode 2: The Design Process
Ultimately, the manufacturing process is an exercise in information sharing. You, the designer, need to pass all pertinent aspects of the design to your manufacturing partners, and the manufacturers need to pass information about their processes to you. Matt starts Episode 2 with a discussion about design for manufacturing (DFM) tools.
The DFM tool is essentially an automated way for the manufacturer to communicate process requirements to designers. After the design is complete and the DFM checks have been run, you need to accurately communicate your design to the manufacturing partner. The manufacturing files are the primary tool you have at your disposal to deliver your design. Matt gives pros and cons of different formats and notes the formats that ASC Sunstone prefers.
Episode 3: CAM, Materials, and Imaging
If you’ve ever looked at a circuit board and wondered how the PCB fab shop built it, this episode is for you. Matt starts explaining the process with the yellow light of photoresist imaging. This is one of the shorter episodes in the set, but it gives an understanding of the imaging and etch process. In 15 minutes, you will have a better understanding of why “space and trace” dimensions are so important. You’ll hear about optical limits, laser direct imaging and how both technologies work toward giving you a reliable design.
Episode 4: Lamination
The title “Lamination” doesn’t really do justice to the subject of this episode. This installment is about putting together the layers of the circuit board. Matt starts by discussing registration—keeping the layers aligned with each other. While you, as the designer, may not have much effect on registration, an understanding of what goes into lining up the PCB layers will help you know what is important when laying out multilayer designs. Matt’s knowledge of the process should also give you confidence that if you have done your job right, he will as well.
Matt gives advice on reducing the opportunities for error. Fab shops can build high-layer-count boards, but reducing the number of layers when possible, using larger vias if possible, and considering what is going on between the top and bottom surfaces will help ensure a successful design.
Episode 5: The Intricacies of PCB Drilling
Before I worked in manufacturing, as a circuit board designer vias were simply a way to get a signal from one layer to another. I called out one drill size for all signals, another for power, and gave it little thought beyond that. After I set my professional self into a manufacturing facility, I quickly learned how much more there is to the humble drill hole, especially in high performance designs. Matt covers this subject and more in this segment. There is a lot more than just drills here.
Takeaways
I hope I haven’t given away too much of the content. If I have, there are seven more episodes to go, so there are plenty of unspoiled episodes still to come. Most are around 25 minutes, so it’s something you can easily listen to over lunch or on your drive to work. (Click here to listen.)
The real takeaway from the series is to think beyond just the electronic circuit. Design really needs to be a holistic activity that considers all aspects of the product from day one. In the same way that you need to consider the environmental conditions your product will need to operate under, you also need to consider the manufacturing shops where it will be built. It’s not a great design if it won’t function under real-world conditions, and it’s not a great design if it can’t be reliably built.
Ideally, product development is a partnership between the design team, board fabrication house, and assembly manufacturer. It’s a balance between pushing design limits and reducing risk by backing off from those limits when possible. Knowing your manufacturing partners well will contribute to the project's ultimate success.
Duane Benson is a technology journalist and consultant operating as Positive Edge LLC. He has 30+ years of experience in the electronics design and manufacturing industry as a developer, executive, speaker, and writer. You can reach Duane at duane@positiveedge.today.
Suggested Items
Spring 2024 Santa Clara County Flexfactor Finals Held at Nextflex
05/20/2024 | NextFlexNextFlex hosts this semester’s FlexFactor. Four teams of high school students competed by pitching their inventive products to a panel of esteemed judges composed of Robert de Neve, General Partner & Chief Strategist General Partner & Chief Strategist at NextPhase Ventures; Christine Holly Ngo, VP of Operations and Business Development at Silicon Valley Elite Manufacturing, Inc; and Jackson Rambough, FHE Design and Process Engineer at NextFlex.
Würth Elektronik in United States Embarks on New Milestone with State-of-the-Art Headquarters
05/17/2024 | Wurth ElektronikWürth Elektronik in the United States, a leading manufacturer of electronic and electromechanical components as well as custom magnetics, has announced the commencement of construction on a new 70,000-square-foot headquarters. This new facility underscores the company’s commitment to innovation and grow in the electronics industry.
IPC APEX EXPO: Some Thoughts About Growth
05/16/2024 | Dan Feinberg, I-Connect007After two and a half days of wandering the aisles at IPC APEX EXPO 2024, for the first time, I almost felt like I was exploring CES. There were so many booths and exhibits that I could describe, but I’d like to focus on the growth and huge value of this event, which has expanded well beyond just the growing and impressive exhibit show floor.
Airbus Achieves Eurodrone’s Preliminary Design Review
05/16/2024 | AirbusThe Eurodrone programme has successfully performed the Preliminary Design Review (PDR). Led by Airbus Defence and Space as prime contractor, this major programme milestone has been completed with OCCAR and representatives of the four customer nations (France, Germany, Italy and Spain) in the presence of the three Major Sub-Contractors (MSC), Airbus Defence and Space Spain, Dassault Aviation and Leonardo.
A Review of the 2024 Del Mar Electronics and Manufacturing Show
05/16/2024 | Barry Matties, I-Connect007The Del Mar Electronics and Manufacturing Show (DMEMS) in Del Mar, California, recently took place at an unlikely venue: the Del Mar Fairgrounds. Doug Bodenstab, founder and show organizer, says the show covers everything in electronics manufacturing: design tools, components, base materials, training, testing, board fabrication, AI, data analytics, and more. While you can find about anything online these days, Bodenstab adds that there is no substitute for meeting people in person.