HDI Design Education: Is Anyone Interested?


Reading time ( words)

I first became aware of high-density interconnection (HDI) design methodology in 1997 when a co-worker of mine came back from a training class that was taught by Happy Holden. “Little Dave” (since our department had two employees named David W.) came back excited to try this new design knowledge on a multilayer board stackup that only used blind and buried vias, with no through-hole vias. His excitement and dedication paid off, as he completed the design with an autorouter exactly as he planned. Through Dave’s success, our department then started to create other designs using HDI stackups that were taught in Happy’s class and our autorouter tool.

I did a few complex designs that fit into the IPC Type III category. One of the more complex designs I attempted could only autoroute up to 98% completion after trying many setup files (with great assistance from “Big Dave”) and our most powerful computer available within our group. I finished the design manually, and the board was fabricated and worked as designed.

About six months later, when we upgraded our department’s autorouter computer, I restored the design from archive, and re-ran the last autorouter configuration file on that 98% completed design. This time, the design was now 100% completely autorouted, and took about a third less time than on the previous “most powerful” computer. This one little re-investigation became the catalyst for my full immersion into HDI design research, reviewing the existing designs and now trying newer autorouting approaches with a variety of more challenging stackups, via spans, and via sizes. Each new redesign attempt created more curiosity to push autorouters and stackup methodologies to their absolute limits.

Over the next few years, any article written on HDI that crossed my path became assimilated into my mental database. I met Mike Fitts lecturing on HDI at a design conference, and I asked him to clarify my repository of HDI re-design questions. When Mike and I met at another design conference, he introduced me to the very person who inspired Little Dave: Happy Holden.

Read the full column here.


Editor's Note: This column originally appeared in the May 2014 issue of The PCB Design Magazine.

I first became aware of high-density interconnection (HDI) design methodology in 1997 when a co-worker of mine came back from a training class that was taught by Happy Holden. “Little Dave” (since our department had two employees named David W.) came back excited to try this new design knowledge on a multilayer board stackup that only used blind and buried vias, with no through-hole vias. His excitement and dedication paid off, as he completed the design with an autorouter exactly as he planned. Through Dave’s success, our department then started to create other designs using HDI stackups that were taught in Happy’s class and our autorouter tool.

I did a few complex designs that fit into the IPC Type III category. One of the more complex designs I attempted could only autoroute up to 98% completion after trying many setup files (with great assistance from “Big Dave”) and our most powerful computer available within our group. I finished the design manually, and the board was fabricated and worked as designed.

About six months later, when we upgraded our department’s autorouter computer, I restored the design from archive, and re-ran the last autorouter configuration file on that 98% completed design. This time, the design was now 100% completely autorouted, and took about a third less time than on the previous “most powerful” computer. This one little re-investigation became the catalyst for my full immersion into HDI design research, reviewing the existing designs and now trying newer autorouting approaches with a variety of more challenging stackups, via spans, and via sizes. Each new redesign attempt created more curiosity to push autorouters and stackup methodologies to their absolute limits.

Over the next few years, any article written on HDI that crossed my path became assimilated into my mental database. I met Mike Fitts lecturing on HDI at a design conference, and I asked him to clarify my repository of HDI re-design questions. When Mike and I met at another design conference, he introduced me to the very person who inspired Little Dave: Happy Holden.

Read the full column here.


Editor's Note: This column originally appeared in the May 2014 issue of The PCB Design Magazine.

Share


Suggested Items

PCB Design Challenges: A Package Designer’s Perspective

09/17/2018 | Bill Acito, Cadence Design Systems
The challenges faced by the PCB designers of today are significant. If we examine the breadth of designs, we find ever-increasing data rates and more high-speed signal routing that drive additional challenges meeting signal-quality requirements, including reflection signal loss and crosstalk issues. At the same time, designers are being asked to complete designs in shorter cycle times and in smaller form factors. They must come up with new and more complex routing strategies to better control impedance and crosstalk. Manual implementation is often time-consuming and prone to layout errors.

Managing the Challenges of Flex and Rigid-Flex Design

09/12/2018 | Dave Wiens, Mentor, a Siemens Business
PCB designers working with flex or rigid-flex technology face many potential risks that can derail a project and cause costly design failures. As the name implies, flex and rigid-flex designs comprise a combination of rigid and flexible board technologies made up of multiple layers of flexible circuit substrates, attached internally and/or externally to one or more rigid boards. These combinations provide flexibility for the PCB designer working on dense designs that require a specific form factor. Rigid-flex allows the PCB design team to cost-efficiently apply greater functionality to a smaller volume of space, while providing the mechanical stability required by most applications.

Mentor Preparing for Next-Gen PCB Designers

08/20/2018 | Andy Shaughnessy, Design007 Magazine
Millennials are the future of our industry. What does this mean for the PCB design community? How do we attract more of these smart young people to the world of PCB design? I asked Paul Musto, director of marketing for Mentor’s Board Systems Division, to explain the company’s initiatives aimed at drawing more young people into PCB design



Copyright © 2018 I-Connect007. All rights reserved.